時間:2015-06-28 00:00:00 來源:IT貓撲網 作者:網管聯盟 我要評論(0)
靜態nat與標準acl 的混合使用
??? <1>、將pc0和pc1得ip轉換為環回地址。
??? <2>、阻止1.1.1.2 的通信
??? Router 1配置:
??? Router>en
??? Router#conf t
??? Enter configuration commands, one per line.? End with CNTL/Z.
??? Router(config)#int f 0/0
??? Router(config-if)#ip add 1.1.1.1 255.0.0.0
??? Router(config-if)#no shut
??? %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
??? %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
??? Router(config-if)#int f0/1
??? Router(config-if)#ip add 2.2.2.1 255.0.0.0
??? Router(config-if)#no shutdown
??? %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
??? Router(config-if)#exit
??? Router(config)#
??? %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
??? Router(config)#int loopback 0
??? %LINK-5-CHANGED: Interface Loopback0, changed state to up
??? %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
??? Router(config-if)#ip add 4.4.4.1 255.0.0.0
??? Router(config-if)#no shut
??? Router(config-if)#exit
??? Router(config)#router rip
??? Router(config-router)#network 1.0.0.0
??? Router(config-router)#network 2.0.0.0
??? Router(config-router)#network 4.0.0.0
??? Router(config-router)#end
??? %SYS-5-CONFIG_I: Configured from console by console
??? Router#show ip rou
??? Router#show ip route
??? Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
???? D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
???? N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
???? E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
???? i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
???? * - candidate default, U - per-user static route, o - ODR
???? P - periodic downloaded static route
??? Gateway of last resort is not set
??? C??? 1.0.0.0/8 is directly connected, FastEthernet0/0
??? C??? 2.0.0.0/8 is directly connected, FastEthernet0/1
??? R??? 3.0.0.0/8 [120/1] via 2.2.2.2, 00:00:11, FastEthernet0/1
??? C??? 4.0.0.0/8 is directly connected, Loopback0
??? Router#configure terminal
??? Enter configuration commands, one per line.? End with CNTL/Z.
??? Router(config)#ip nat inside source s
??? Router(config)#ip nat inside source static 1.1.1.2 4.4.4.2
??? Router(config)#ip nat inside source static 1.1.1.3 4.4.4.3
??? Router(config)#interface fastEthernet 0/0
??? Router(config-if)#ip nat in
??? Router(config-if)#ip nat inside
??? Router(config-if)#no shut
??? Router(config-if)#no shutdown
??? Router(config-if)#int f0/1
??? Router(config-if)#ip nat outside
??? Router(config-if)#end
??? %SYS-5-CONFIG_I: Configured from console by console
??? Router#show ip nat ?
????? statistics??? Translation statistics
????? translations? Translation entries
??? Router#show ip nat tr
??? Router#show ip nat translations
??? Pro? Inside global???? Inside local Outside local????? Outside global
??? ---? 4.4.4.2???? 1.1.1.2????? ---??? ---
??? ---? 4.4.4.3???? 1.1.1.3????? ---??? ---
??? Router#ping 3.3.3.2
??? Type escape sequence to abort.
??? Sending 5, 100-byte ICMP Echos to 3.3.3.2, timeout is 2 seconds:
??? !!!!!
??? Success rate is 100 percent (5/5), round-trip min/avg/max = 62/62/63 ms
??? Router#conf
??? Configuring from terminal, memory, or network [terminal]?
??? Enter configuration commands, one per line.? End with CNTL/Z.
??? Router(config)#acc
??? Router(config)#access-list ?
????? <1-99>???? IP standard access list
????? <100-199>? IP extended access list
??? Router(config)#access-list 1 ?
????? deny??? Specify packets to reject
????? permit? Specify packets to forward
????? remark? Access list entry comment
??? Router(config)#access-list 1 deny ho
??? Router(config)#access-list 1 deny host 1.1.1.2
??? Router(config)#access-list 1 per
??? Router(config)#access-list 1 permit any
??? Router(config)#exit
??? %SYS-5-CONFIG_I: Configured from console by console
??? Router#show acc
??? Router#show access-lists
??? Standard IP access list 1
? deny host 1.1.1.2
? permit any
??? Router#configure terminal
??? Enter configuration commands, one per line.? End with CNTL/Z.
??? Router(config)#interface fastEthernet 0/0
??? Router(config-if)#ip access-group 1 in
??? Router(config-if)#no shut
??? Router(config-if)#
??? Router(config-if)#
#p#副標題#e#
Rourer 1 的配置:
??? Router>en
??? Router#conf t
??? Enter configuration commands, one per line.? End with CNTL/Z.
??? Router(config)#int f0/0
??? Router(config-if)#ip add 3.3.3.1 255.0.0.0
??? Router(config-if)#no shutdown
??? %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
??? %LINEPROTO-5-UPDOWN
關鍵詞標簽:靜態NAT,標準ACL
相關閱讀
熱門文章 路由器地址大全-各品牌路由設置地址 各品牌的ADSL與路由器出廠默認IP、帳號、密碼 Nslookup命令詳解-域名DNS診斷 站長裝備:十大網站管理員服務器工具軟件
人氣排行 各品牌的ADSL與路由器出廠默認IP、帳號、密碼 路由器地址大全-各品牌路由設置地址 騰達路由器怎么設置?騰達路由器設置教程 ADSL雙線負載均衡設置詳細圖文教程 路由表說明(詳解route print) Nslookup命令詳解-域名DNS診斷 網管員實際工作的一天 網管必會!了解交換機控制端口流量